How to Do a Door Lock Change

Change your door lock is an easy and inexpensive method to increase the security of your home. However, the procedure is not for everyone. It requires a certain amount patience and expertise.

The cylinder is contained within the knob's body. The cylinder is responsible to recognize the key when it is inserted into the lock.

Removal of the old lock

First, remove the lock that was previously in place. It is a fairly easy process, but you should keep some things in mind. First, ensure that your new lock is the correct size for your door. This will ensure that it fits snugly and does not create a gap around the deadbolt plug or latch.

After you have removed the latch plate, you will have to look for two screws or bolts on the inside of casing which are holding the casing together with the two halves of the lock. Unscrew them using a screwdriver and then remove the lock from the door. If you have a mortise locking mechanism there is a set screw that holds the handle to the spindle. Take off the doorknobs by removing this screw using a screwdriver.

You must also take the deadbolt and latch plug from the hole in your door jamb. Install your new lock. If you're replacing a mortise, you should take a measurement of the distance between the lock case and your door's edge to make sure that the new lock is a good fit.

There are a variety of reasons that could prompt you to replace your door lock, such as being concerned that someone else may have the key, or you are welcoming an incoming roommate. You can save money by deciding to remove the lock yourself instead of hiring for a professional. It's much easier than you think and can be done in a matter of a few minutes.

Remove the trim and handle of your door. Then, pull the trim away with a flat screwdriver. You should be able to twist off the majority of it, and in some cases the handles could come off completely. The next step is to look for a pinhole on the inside of the handle, and insert straightened clips into it. This will activate the release mechanism and allow you to take the handle from the door. Then, look for a small tab in the interior of the lock and push it with a screwdriver that is flat. After the spindle is removed, you can remove the housing and cylinder.

The choice of a new locking system

When it comes to choosing the right lock for your home you have a variety of options. Think about the various kinds of locks and choose one that matches the design of your door. Consider the backset which is the distance between the edge and the center of the hole for the lock. Also consider the cross bore, a small hole in the middle of your door's frame. Also, be sure to choose a lock that will be able to fit the door's thickness and swing.

Most door locks are evaluated by BHMA and the American National Standards Institute to give you an idea of how well they are able to withstand the rigors of use and how difficult to disable or pick. A grade 3 lock could be ideal for a quiet urban apartment complex, whereas an entry grade window lock replacements could stand up to the traffic near a busy storefront on a busy city street.

Most smart door locks require digital code to open. If you are worried about hacking or other security issues, talk to an expert locksmith.

replace window lock the cylinder

You can easily replace damaged or broken doors lock cylinder by doing a simple DIY project. The key is to select the right cylinder, and follow the directions that accompany it. The first step is to take off the knob or handle, in the event that one is present then loosen the trim that is attached to the base of the lock cylinder using a screwdriver. Once the trim has been removed, it is possible to remove the screws that hold the cylinder with a flathead. The cylinder is then gently removed from the door.

Make sure you take measurements of the length of the new cylinder prior to installing it. With an instrument, measure the distance between the cylinder's center and its left and right sides. Then, buy a new cylinder with the same measurements. This will prevent cylinders from snapping when doors are kicked or the key becomes stuck inside.

Once you have a suitable replacement cylinder, place it in the door and turn the key. This will ensure that the cylinder is aligned with the carrier, which is typically located on the outside of the lock. Then, loosen the set screw which is supposed to be a few turns inside the head. If there is a screw on the edge of the case that holds the door, you will need to remove it.

You can replace the old lock cylinder with the new one by sliding it into the case and then tightening the set screws. Installing the part that connects a cylinder with an indicator stem for a lock is also important. You can do this by pulling three tabs in the back of the cylindrical with needle-nosed pliers. Then, you can attach the smaller bracket to the back of the cylinder. You should then reinstall the latch plate and strike plate, along with the retaining rings that are attached to the top of the lock the cylinder.

Installing the new lock

Begin by measuring the door's width if you are replacing a lock that is already in use. Most residential locksets are designed for doors with a thickness of 1 3/8 - 3/4 inch. If your door is thicker, you will need a door kit that is thick and includes longer screws, a longer tail piece (for door knobs) or spindle extension (for deadbolts).

The majority of locks come with a detailed instruction manual to assist you in installing the new hardware. Be sure to read the instructions thoroughly before starting the process to ensure that you are following all of the necessary steps. The manual will give you a clear idea of the level of skill that is required to finish the task. If you're replacing a repair window lock for the first time, you might need to seek out an experienced friend for assistance.

It's a good idea to seal the openings of the old hardware before installing the new lock. This will prevent the screws from falling through the holes, and also protect any tiles you have put in. This will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch includes the masking strip or gaffer tape, but you can make use of any tape you have.

Once you've removed the screws that hold the interior half of the lock section to the exterior side, pull it straight away. It is important to do this quickly to avoid the lock from accidentally closing on itself and damage the mechanism.

Fit the new latch bolt in the upper cross bore of the new lock if it has one. Make sure that you put it in the correct place that is usually indicated by an arrow on the faceplate. Then, place the latch plate onto the bolt and secure it in place.

Finally, screw in the deadbolt and strike plate into the door jamb. Test the deadbolt a few times by throwing it to make sure it extends into the strike plate. If you're using an electronic smart repair window lock, make certain to follow the instructions for programming it. This requires downloading an application and registering your e-mail address, verifying you identity, and connecting to the wireless network to connect your device.