Car Key Button Repair

A broken car key button can be a hassle. You may need to contact an emergency locksmith service or purchase an alternative remote key repair.

But, you may be in a position to save money by fixing an old key fob rather than replacing it. This is especially true if the issue is caused by a worn switch or faulty contact.

Battery

If the buttons on your key fob do not respond when you pressing them, this could be a sign that the battery is dead or is about to reach the end of life. Fortunately, replacing the battery is a simple task that can be done by yourself rather than paying a locksmith or dealership to take care of it.

First find the battery compartment. The battery compartment is typically located on the back of the key fob, and can be concealed behind a cover that can slide out or an open button that opens the access point. Once the compartment is opened you can see the small button cell battery. It is usually shaped like a small coin and marked with an plus and the minus symbol. Remove the battery that is old, and replace it with a new one. Make sure the plus and symbol are aligned correctly.

Once the battery is installed close the compartment and snap the two parts of the key fob together. Before closing the door make sure to align and snap the components into the correct position. Press any of the buttons to ensure that they function correctly.

If your remote key repair key fob stops functioning even after replacing the battery, it may be suffering from other issues that require a different kind of repair keys near me. Dropping the device into a puddle can cause it to stop working. It could also be a problem with the internal electrical system or the need to be deprogrammed. See if you can find out if the problem is with your key fob using these other automotive troubleshooting methods.

Switches

There are many kinds of switches that are used in the mobile car key repair key fob according to the year and model. The older style key is equipped with an electronic chip that is visible in the case. The modern keys function by sending signals to your car key fob repairs near me. Regardless of the type of key, the keys' buttons can get worn down or damaged during normal use. They become difficult to press or ineffective. If you press the button too hard it could cause more damage. It could also stop the key from functioning in the future.

If your key doesn't seem to be working, first try changing the battery. If this doesn't work, you might need to clean your key's fob or adjust the switches. These tiny electronic switches are more likely than the larger parts of the key to break since they are constantly tossed about.

The switches feel rubbery and are coated with a film that conducts electricity. The film may fade over time. Luckily, they're also a very small part and affordable to replace. They're soldered on the circuit board, therefore you must carefully take them off without causing any damage to any other part of the circuit. You can then solder the new ones into and then reassemble your fob.

A good way to keep your car key fob from getting ruined is to avoid using it for longer than a couple of hours at a stretch, and to avoid leaving it in visible locations where it can be seen. Also, you should locate a safe place to store your keys when you aren't making use of it.

If the issue continues to persist after you've cleaned your key fob replaced the battery and attempted to clean it, then you may need to consult an expert locksmith. A professional locksmith can check your key's frequency to see whether your vehicle is capable of communicating. They can also open and replace microswitches, change cases, and much more.

Outer Case

If the buttons aren't able to move freely in the case, they could become stuck or break. If changing the battery or cleaning it with the help of a cotton swab or alcohol rubbing doesn't solve the issue, taking off the case and inspecting may be necessary. If the contacts that the buttons touch aren't a good fit or if they're worn, changing them might be the only option.

Certain keys have buttons made of rubber, which wear away over time. The rubber stretches and nails pierce it, and the buttons become difficult to press. This could cause the key to fail, and in this case it is time for the replacement of the case or buttons. This repair involves taking apart your remote, finding the buttons on the board, heating the solder, and carefully taking them off. New buttons are then attached to the circuit board. The case is then put back together with the horseshoe key blade piece is attached. The new buttons must be fitted snugly into the case in order to stop them from falling out.

Inner Case

Since your key fob is likely get jostled around and may occasionally be pressed by accident and the buttons within can become stuck or broken over time. If your key fob ceases to function when you're away from home, you can solve the issue quickly using metallic tape and a punch hole. This will allow you to open doors, but not start the vehicle. This quick fix could enable you to safely make it back to your vehicle and complete your journey.